blog_banner

BLOG DETAIL

Home How PMI Foam Core Is Used in Racing Car Body Panels and Wings
Inquire

Table of Contents

Racing car body panels and aerodynamic wings have one important requirement in common: they must remain stiff without adding unnecessary weight. A rear wing that deflects under aerodynamic load can change its intended profile, while a large body panel needs enough rigidity to withstand vibration and handling without excessive reinforcement.

Carbon fiber is a common choice for these components, but a solid carbon fiber laminate is not always the most weight-efficient solution. Where bending stiffness is the main design requirement, a sandwich structure can provide better use of material.

PMI foam core (polymethacrylimide foam) is a lightweight structural material used between carbon fiber skins. It allows engineers to increase panel thickness and bending stiffness while keeping the core relatively light.

In racing car composites, PMI foam is particularly relevant to body panels, wing elements and other shaped structures manufactured using carbon fiber prepreg or suitable resin-based processes.

Understanding how the foam works, where it should be used and how to select the right grade is essential before incorporating it into a racing component.

Custom-Size PMI Foam Core Panels.jpg

1. Why Racing Car Manufacturers Use PMI Foam Core

A racing car contains many components that do not need to be solid throughout their thickness. Exterior panels and selected aerodynamic surfaces are examples where the distribution of material can matter more than the amount of material used.

In bending, the outer surfaces of a panel carry much of the tensile and compressive stress. By separating these surfaces with a lightweight core, a sandwich panel can achieve higher bending stiffness than a similarly weighted solid laminate.

1.1 The Function of PMI Foam in Carbon Fiber Sandwich Panels

A typical carbon fiber sandwich panel consists of:

· An outer carbon fiber reinforced polymer (CFRP) skin.

· A structural PMI foam core.

· An inner carbon fiber skin.

The carbon fiber skins provide in-plane strength and stiffness, while the foam core maintains their separation and transfers shear loads between them.

This construction is useful for large surfaces where deflection must be controlled without making the entire panel substantially heavier.

PMI foam also provides a machinable internal structure that can be shaped to match curved composite components.

1.2 What Makes PMI Foam Suitable for Motorsport?

Several characteristics make PMI structural foam worth considering for high-performance racing composites.

Low density: The core adds thickness without the weight associated with an equivalent thickness of solid composite material.

Mechanical performance: Suitable PMI grades provide compressive and shear properties needed for structural sandwich construction.

Processing resistance: Selected grades can withstand elevated-temperature composite manufacturing, including certain prepreg curing cycles.

Machinability: PMI foam sheets can be CNC-machined into complex profiles, tapered sections and variable-thickness cores.

Closed-cell structure: Resin penetration is generally limited to cells opened at the foam surface, helping control unnecessary resin uptake.

These characteristics vary by foam formulation and density. The suitability of a particular grade must be verified against the manufacturing process and expected component loads.

2. PMI Foam Core in Racing Car Body Panels

Large racing car body panels often require substantial bending stiffness even when they are not primary load-bearing structures.

Typical examples include engine covers, removable exterior panels, access covers and selected roof or bodywork sections.

2.1 Carbon Fiber Engine Covers and Exterior Panels

An engine cover may have a relatively large unsupported area, with attachment points concentrated around its edges.

A thin carbon fiber laminate can be light, but insufficient bending stiffness may result in unwanted deflection or vibration.

One solution is to incorporate a PMI foam core between carbon fiber skins in selected regions.

The foam increases the separation between the skins, making it possible to improve panel stiffness without relying exclusively on additional carbon fiber layers.

2.1.1 Where the Core Is Most Useful

PMI foam is especially useful in broad panel sections where distributed bending stiffness is required.

However, mounting positions, hinges and latches introduce concentrated loads that must be treated differently from the main panel surface.

These areas may require additional reinforcement, higher-density inserts or solid laminate construction.

2.1.1.1 Local Reinforcement Around Mounting Points

Fasteners should not automatically transfer high concentrated loads directly into a low-density foam core.

Depending on the load, designers may use bonded inserts, reinforced laminate zones or localized core replacement.

The interface between the reinforced region and the surrounding sandwich structure should be designed to avoid abrupt stiffness changes and premature damage.

2.2 Curved Bodywork and Complex Panel Geometry

Many racing car exterior parts have complex curves rather than simple flat surfaces.

The foam core must follow these contours without introducing gaps, excessive local stresses or dimensional errors.

CNC machining allows a PMI foam sheet or block to be prepared according to the required three-dimensional geometry.

For components with variable curvature, the core may be machined with tapered edges or different thicknesses in specific regions.

This approach can help manufacturers produce shaped carbon fiber sandwich panels while maintaining the intended exterior geometry.

2.3 When a Solid Carbon Fiber Laminate May Be Better

Not every racing car panel needs a foam core.

Very small components, thin mounting flanges and highly concentrated load areas may be more efficiently produced using solid carbon fiber laminates.

Sandwich construction introduces additional considerations, including core preparation, bonding, edge finishing and moisture protection where required.

The decision should therefore be based on the complete component rather than the assumption that a foam sandwich is always lighter.

PMI Foam Core for Aerospace Composites.jpg

3. PMI Foam Core in Racing Car Wings

Front wings and rear wings are among the most demanding aerodynamic components on a racing vehicle.

Their purpose is to generate and control aerodynamic forces. Structural deformation under these forces must be considered during design.

A lightweight wing must maintain sufficient stiffness while meeting the aerodynamic and structural requirements of its racing category.

3.1 Rear Wing Sandwich Construction

A rear wing may contain curved carbon fiber skins, internal supporting structures and locally reinforced attachment points.

In suitable wing designs, PMI foam can form part of the internal sandwich construction.

It helps separate the carbon fiber skins and supports the aerodynamic surface while contributing to the overall structural stiffness.

The foam may be machined to follow the wing's airfoil geometry before the carbon fiber layers are applied.

3.1.1 Controlling Wing Deflection

As aerodynamic loading increases, the wing experiences bending and potentially twisting.

Excessive deformation can alter the intended airfoil shape and affect aerodynamic behavior.

A correctly designed carbon fiber sandwich section can resist bending efficiently, but the wing must also be evaluated for torsional stiffness, local stability and attachment loads.

Core thickness, carbon fiber fiber orientation and internal reinforcement all influence the final result.

3.1.2 Core Design Near Wing Supports

Wing supports and endplate connections can introduce concentrated forces into the structure.

These areas may require internal spars, reinforced ribs, structural inserts or solid laminate regions.

PMI foam should not be treated as a direct substitute for reinforcement designed to carry concentrated loads.

3.2 Front Wings and Multi-Element Aerodynamic Parts

Front wing designs may involve multiple airfoil elements with different dimensions, curvature and structural requirements.

For selected elements, a machined PMI foam core can provide the internal shape needed to support thin carbon fiber skins.

However, some wing elements may be too thin or geometrically restricted for an effective foam sandwich solution.

Material selection must therefore consider the available internal thickness and the manufacturing method.

3.3 Surface Quality and Dimensional Accuracy

Aerodynamic components require controlled surface geometry.

A machined core can help establish the intended internal profile, but the finished surface also depends on mold accuracy, laminate placement, resin distribution and cure-related deformation.

Designers should consider the possibility of core or bond-line print-through, particularly when using thin outer skins.

PMI foam contributes to the structure, but accurate aerodynamic surfaces require control of the complete composite manufacturing process.

4. Designing Carbon Fiber Sandwich Structures with PMI Foam

The mechanical advantage of a sandwich structure comes from the relationship between the face sheets and the core.

Increasing core thickness generally increases the distance between the load-bearing carbon fiber skins. This can improve bending stiffness, provided the foam and bonding interfaces can withstand the resulting loads.

4.1 Core Thickness and Bending Stiffness

A thicker core can be effective for large panels, but increasing thickness also affects weight, overall dimensions and shear deformation.

The optimum thickness depends on panel span, expected loads, laminate design and allowable deflection.

For a broad body panel, bending stiffness may be the main concern.

For a wing, torsional stiffness and local loading may become equally important.

4.2 Core Shear and Compression

Two important mechanical properties of structural PMI foam are shear performance and compressive resistance.

Shear strength and modulus influence the foam's ability to transfer loads between the carbon fiber skins and limit shear deformation.

Compressive strength and modulus influence resistance to local pressure, concentrated loading and certain manufacturing stresses.

Selecting a core based only on density can result in an unsuitable material.

4.3 Skin-to-Core Bonding

The bond between the carbon fiber skins and PMI foam must transfer the forces required by the sandwich design.

Poor bonding can cause delamination or premature structural failure even when the individual materials have adequate strength.

4.3.1 Preparing the Bonding Surface

Important considerations include surface cleanliness, removal of machining dust, resin compatibility and suitable adhesive application.

The foam's surface cell structure can also influence resin uptake and bond-line behavior.

4.3.1.1 Validating the Bonding Process

Before production, representative samples should be manufactured using the intended materials and cure cycle.

Relevant tests may include flatwise tensile strength, core shear, compression and other evaluations according to the expected loading conditions.

5. Processing PMI Foam for Racing Car Composites

Racing car components are commonly manufactured using carbon fiber prepreg, vacuum processing and other composite molding techniques.

The choice of PMI foam must account for the complete manufacturing cycle.

5.1 PMI Foam with Carbon Fiber Prepreg

Prepreg manufacturing allows controlled fiber placement and resin content.

For sandwich construction, the PMI foam core may be placed between prepreg layers and processed using an appropriate curing method.

Depending on the materials, the process may involve an oven, autoclave or other controlled curing equipment.

Selected PMI foam grades are suitable for elevated-temperature processing, but no single curing limit applies to every PMI material.

5.1.1 Temperature and Pressure Compatibility

Engineers should evaluate:

· Maximum curing temperature.

· Applied vacuum and consolidation pressure.

· Time at elevated temperature.

· Dimensional changes during curing.

· Core compressive creep.

· Resin and adhesive compatibility.

A foam that tolerates a certain temperature under minimal load may deform when exposed to the same temperature under higher pressure.

5.1.1.1 Core Conditioning Before High-Temperature Curing

Some PMI foam products require controlled drying or heat treatment before demanding curing cycles.

The need for conditioning depends on the specific material and processing conditions.

Such treatment may affect core dimensions, so manufacturers should follow the grade-specific recommendations before final machining and layup.

5.2 CNC Machining of PMI Foam

CNC machining is particularly relevant to body panels and aerodynamic components with complex internal geometry.

Typical operations include milling, drilling, routing and tapered-edge machining.

Machining must be controlled to avoid damaging the foam structure or compromising dimensional accuracy.

For high-precision applications, it is useful to review the core's final geometry together with the composite mold design.

5.3 Vacuum Infusion and Alternative Manufacturing Methods

PMI foam may also be considered for vacuum infusion and resin transfer molding, depending on the product grade and component requirements.

Because PMI foam has a closed-cell structure, resin does not normally flow through the intact foam interior.

An appropriate resin-flow strategy may therefore be required, particularly for larger sandwich panels.

Resin penetration into cut surface cells, adhesive consumption and local edge sealing can influence finished component weight.

6. Selecting PMI Foam Core for Racing Car Body Panels and Wings

Selecting the right PMI foam requires a balance between density, structural performance, manufacturing conditions and cost.

A low-density foam may reduce weight, but it will not necessarily provide adequate compression or shear resistance for every component.

6.1 Matching PMI Foam Properties to Component Requirements

The following table summarizes the main engineering considerations.

Component

Main Design Requirement

Core Selection Focus

Engine cover

Low weight and panel rigidity

Density, core thickness, bending stiffness

Exterior body panel

Shape retention and vibration resistance

Shear modulus, thickness, bonding

Rear wing

Bending and torsional control

Shear properties, compression, core geometry

Front wing element

Thin aerodynamic profile

Machinability, available thickness, local reinforcement

Aerodynamic fairing

Complex shape and dimensional accuracy

CNC machining, density, processing stability

Diffuser section

Panel stiffness and service durability

Mechanical properties, impact and abrasion exposure

These considerations are starting points rather than fixed specifications. Final core density and thickness should be determined through component design and testing.

6.2 PMI Foam Compared with PVC and PET Foam Core

PMI, PVC and PET structural foams can all be used in composite sandwich structures.

However, they differ in mechanical properties, thermal resistance, processing behavior and cost.

PMI foam is often considered for demanding composite manufacturing where the required combination of low density, structural properties and elevated-temperature processing capability justifies its use.

PVC and PET foam may provide economical alternatives for components manufactured at lower temperatures or with different structural requirements.

The comparison must be made between specific commercial grades rather than broad material categories.

6.3 Questions to Ask Before Choosing a Core

Before ordering PMI foam for a racing composite project, engineers should establish the following:

1. Is the part primarily stiffness-controlled or strength-controlled?

2. What are the expected bending, shear and local compression loads?

3. What core thickness is available?

4. Is the manufacturing process prepreg, infusion or secondary bonding?

5. What are the curing temperature and pressure?

6. Does the part require CNC-machined core geometry?

7. Are there demanding impact, vibration or service-temperature conditions?

Clear answers help narrow the selection of suitable structural foam core materials.

·PMI Foam Core for Composite Manufacturing.jpg

7. JLON PMI Foam Core for Motorsport Composite Manufacturing

JLON supplies PMI foam core materials for lightweight composite sandwich applications.

Our product range supports customers working with carbon fiber composites, precision-machined core structures and advanced lightweight components.

For racing car body panels and aerodynamic structures, JLON can assist customers in reviewing material requirements and identifying suitable PMI foam options.

7.1 Material Selection and Technical Support

Project discussions can cover foam density, required dimensions, thickness, manufacturing methods and mechanical specifications.

Customers using carbon fiber prepreg should provide the intended curing temperature, pressure and cycle duration.

This information helps determine whether a proposed PMI foam grade is appropriate for the manufacturing process.

7.2 Custom Requirements and Sample Evaluation

Motorsport composite projects often involve custom component geometry and relatively demanding production requirements.

JLON can review requests for sheet materials, specific dimensions and machining requirements according to product availability and project specifications.

For prototype development, sample evaluation is recommended before committing to production quantities.

Customers should confirm the applicable technical datasheet and any required test documentation for the selected material.

8. Frequently Asked Questions

Is PMI foam core suitable for racing car body panels?

Yes, PMI foam can be used in carbon fiber sandwich body panels where stiffness and weight are important design considerations. The suitability of the complete panel depends on its laminate design, mounting arrangement and expected loads.

Why is PMI foam used in carbon fiber racing wings?

A PMI foam core can support the carbon fiber skins and contribute to the bending stiffness of suitable wing sections. The complete wing may also require spars and local reinforcement to carry aerodynamic and attachment loads.

Can PMI foam be CNC-machined into aerodynamic profiles?

Yes. PMI foam can be machined into complex shapes using suitable CNC equipment. Machining capability and dimensional tolerances should be verified for the selected grade.

Can PMI foam withstand autoclave curing?

Selected PMI foam grades are compatible with autoclave processing. Maximum allowable temperature, pressure and exposure time depend on the material grade and any required conditioning treatment.

How do I choose the correct PMI foam density?

Density should be selected according to component loads, required stiffness, core thickness and manufacturing conditions. Mechanical properties from the relevant TDS should be reviewed before making the final selection.

9. Conclusion

PMI foam core is a practical structural material for selected racing car body panels and aerodynamic components where a carbon fiber sandwich construction offers advantages over a solid laminate.

Its main contribution is not simply reducing material weight. The core allows engineers to position carbon fiber skins more efficiently, providing bending stiffness and supporting complex component geometries.

For body panels, attention should be given to panel span, mounting points and local reinforcement. For wings, aerodynamic loading, torsional stiffness and internal support structures are equally important.

Manufacturing conditions also influence the choice of PMI foam, particularly when prepreg curing involves elevated temperatures and pressure.

JLON supplies PMI foam core for carbon fiber sandwich composite applications. Contact JLON with your component drawings, required density, thickness and curing conditions to discuss suitable materials and sample requirements.

Contact Us